510 513 150KN Escalator Step Axle Chain from factory

JIEFENG GROUP, founded in 2007, is a global elevator and escalator parts manufacturer.

Selection of chain drive power

Chain factories with a long history in the world have their chain transmission power rating graph and power diagram. We can refer to the GB/T 18150-2006 / ISO 10823:2004 standard selecting the drive power or selecting the chain according to the drive power, the condition is that we should know the tooth number of the small sprocket and its speed. Only if the actual power is within the range of rating power of the power rating graph, the selected chain is suitable.

Now we use the transmission part in the walking tractor and the transmission power in rotary tillage to prove whether the chain selection is correct.

■ Chain drive part

1.Each sprocket in the driving system should have good coplanarity and the chain path should always be smooth.

2.The sagging of chain loose side should be suitable and for the adjustable center distance level and angle drive, the sagging should be 1%~2% of the center distance. For conditions of vertical drive and under vibration load、reverse drive and dynamic brake ,the sagging should be smaller. It’s very important to check and adjust the loose side sagging frequently in the chain drive maintenance.

3.Good lubrication is also very important. Whichever lubrication method you choose, the most important thing is to make the lubricating grease distribute evenly in each chain joint clearance. If not necessary, avoid selecting big viscosity heavy oil or lubricating grease since it will jam the clearances gone to joints friction surface with dust after a period of time. Periodi- cally clean the roller chain and check its lubrication condition frequently. Disassembly the pin and bush, if necessary. If the friction surface is brown or dust color, it may be caused by insufficient lubrication.

4.Chains and sprockets should be always in good condition.

5.Frequently check the working surface of sprocket teeth ,adjust or replace it when it’s excessively worn.

Troubleshooting Instructions

Failure Symptom	Possible Causes	Actions
Roller cracked or deformed	1. Too big chain pitch or too small number of sprocket teeth 2. Sprocket teeth have foreign bodies. 3.The chain climbs onto sprocket teeth too high. 4.Excessive chain impact load	1. Select small pitch chain or add sprocket teeth number 2. Remove all the foreign bodies or replace chain 3.Replace the chain and make appropriate tensioning 4.Reduce the impact of chain
Pin rotates or plate hole drawn long	1.Chain overloaded	1.Eliminate the overloading causes or adopt large specification chain
Pin broken or plate broken along the hole connecting line direction	1.Excessive overloading	1.Eliminate the overloading causes or adopt large specification or higher strength chain; if sprocket failure symptom found, replace it
Plates broken	1.The load above chain dynamic capacity	1.Selecting big pitch chain or reduce dynamic load
Excessive side-wear of plates or sprocket teeth	1. Sprocket not coplanar or ending beat severely 2. Bad bearing stiffness of sprocket 3.Severe twist of chain	1.Increase machining and installation precision 2.Increase bearing parts stiffness 3.Replace chain
Outer link outside rubbed	1. Chain not tensioned and jump, then to hit adjacent bodies 2. Chain box deformed or with foreign bodies inside	1.Make appropriate chain tensioning 2.Eliminate chain box deformation and remove foreign bodies
Pin worn or bush bonded with pin	1. Bad lubrication 2. Chain speed too high or chain overloaded	1.Supply suitable lubrication system 2.Lower the speed or reduce the load
Excessive wear of sprocket	1. Bad lubrication 2. Inferior material of sprocket and insuffi- cient teeth surface hardness	1.Improve lubrication conditions 2.Improve sprocket material quality and its teeth surface hardness
Locking parts such as spring clip and cotter pin etc. become loose.	1.Chain wobbling heavily 2.Knock with obstructions 3.Locking parts wrong installed	1. Make suitable tensioning or consider adding supporting board for guide plate 2. Remove all obstructions 3. Improve the installation quality of locking parts